Book

 

Right here down the page you can discover additional high-quality data relating to How to Install a Bathtub.

Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately tough project. If the old tub is easily accessible, the job can relocate easily; if you have to open up a wall to eliminate the old tub as well as position the new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also embeded in the new one. See to it you have qualified on your own for the work and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is much better to think about employing one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you mount a new bath tub in your washroom if you have actually already gotten a brand-new bathtub and don't require to change the arrangement of your previous supply of water pipes.
Your devices and also material list need to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome as a result of the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Safeguard the tap in place with the producer given backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Setting up the Tub

Making use of the two wood boards under its feet, position the bathtub in the called for placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water supply as well as check all joints and brand-new pipework for leaks as well as tighten them if needed. Fill up the bath tub as well as likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has actually been utilized at the very least when as this will certainly resolve it right into its final position.

 

 

Planning for the Installment

To start with, the supporting frame provided with the bath ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final position.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealant can fracture relatively early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our part on Installing A Bathtub. Thanks for spending some time to read our blog. Appreciated our write-up? Please share it. Let another person check it out. Thanks so much for going through it.

Schedule An Appointment